Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another
project over the last few months. That is now finished so I can get back
to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and
very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it
shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to
lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
TNG development V6.1.14 released
TNG development V6.1.14 released
Hi Les,
Weren't you working on a lathe CAM at some point?
-----Original Message-----
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: 22 April 2015 14:13
To: sheetcam@yahoogroups.com
Subject: [sheetcam] TNG development V6.1.14 released
Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another project over the last few months. That is now finished so I can get back to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
------------------------------------
Posted by: "Belli Button" <belli@iafrica.com>
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
Weren't you working on a lathe CAM at some point?
-----Original Message-----
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: 22 April 2015 14:13
To: sheetcam@yahoogroups.com
Subject: [sheetcam] TNG development V6.1.14 released
Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another project over the last few months. That is now finished so I can get back to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
------------------------------------
Posted by: "Belli Button" <belli@iafrica.com>
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
TNG development V6.1.14 released
Yes, please!
Andy Wander
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: Wednesday, April 22, 2015 8:57 AM
To: sheetcam@yahoogroups.com
Subject: RE: [sheetcam] TNG development V6.1.14 released
Hi Les,
Weren't you working on a lathe CAM at some point?
-----Original Message-----
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: 22 April 2015 14:13
To: sheetcam@yahoogroups.com
Subject: [sheetcam] TNG development V6.1.14 released
Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another project over the last few months. That is now finished so I can get back to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
__._,_.___
Posted by: "Andy Wander" <andywander@yahoo.com>
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Andy Wander
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: Wednesday, April 22, 2015 8:57 AM
To: sheetcam@yahoogroups.com
Subject: RE: [sheetcam] TNG development V6.1.14 released
Hi Les,
Weren't you working on a lathe CAM at some point?
-----Original Message-----
From: sheetcam@yahoogroups.com [mailto:sheetcam@yahoogroups.com]
Sent: 22 April 2015 14:13
To: sheetcam@yahoogroups.com
Subject: [sheetcam] TNG development V6.1.14 released
Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another project over the last few months. That is now finished so I can get back to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
__._,_.___
Posted by: "Andy Wander" <andywander@yahoo.com>
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
TNG development V6.1.14 released
I'll third that one!
Art
Country Bubba
At 09:01 AM 4/22/2015, you wrote:
__._,_.___
Posted by: Art Eckstein <art.eckstein@gmail.com>
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Art
Country Bubba
At 09:01 AM 4/22/2015, you wrote:
Yes, please!
Andy Wander
From: sheetcam@yahoogroups.com [ mailto:sheetcam@yahoogroups.com (sheetcam@yahoogroups.com)]
Sent: Wednesday, April 22, 2015 8:57 AM
To: sheetcam@yahoogroups.com
Subject: RE: [sheetcam] TNG development V6.1.14 released
Hi Les,
Weren't you working on a lathe CAM at some point?
-----Original Message-----
From: sheetcam@yahoogroups.com [ mailto:sheetcam@yahoogroups.com (sheetcam@yahoogroups.com)]
Sent: 22 April 2015 14:13
To: sheetcam@yahoogroups.com
Subject: [sheetcam] TNG development V6.1.14 released
Hi all,
I have just uploaded V6.1.14 to www.sheetcam.com
Sorry for the long delay for this release. I have been woring on another project over the last few months. That is now finished so I can get back to SheetCam.
Fixed: Crashing on exit on some computers
Fixed: Hint icons being shown much too small.
Fixed: Save job and save job as icon swapped
Fixed: Sometimes not detecting arcs that have a very large radius and very small included angle
Fixed: Rotary plasma plungin sometimes rotating 360 degrees when it shouldn't
Changed: Mode menus now show as radio buttons instead of check boxes
Added: Option to delete contours
Fixed: sometimes generating incorrect leadins
Fixed: Editor not always showing correctly when a Lua macro throws an error
Fixed: Some tools showing incorrect hint icons
Added: Material name (Options->job options->material)
Fixed: Arcs with a huge radius and small included angle are converted to lines
Added: 'Run post' button in post editor
Fixed: Overlapping rules sometimes not output correctly
Les
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
__._,_.___
Posted by: Art Eckstein <art.eckstein@gmail.com>
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Country Bubba
TNG development V6.1.14 released
I have been making internal changes to simplify the addition of lathe
cam but I haven't really started working on it. Lathe is a longer term
project.
Les
On 22/04/2015 13:57, 'Belli Button' belli@iafrica.com [sheetcam] wrote:
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
cam but I haven't really started working on it. Lathe is a longer term
project.
Les
On 22/04/2015 13:57, 'Belli Button' belli@iafrica.com [sheetcam] wrote:
Hi Les,
Weren't you working on a lathe CAM at some point?
------------------------------------
Posted by: Les Newell <les.newell@fastmail.co.uk>
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/