Pierce Delay Wiggle vs No Lead In

[mechanicjon]

When running a gcode file with wiggle pierce I lose the pierce delay for a cut with no lead in thats on a seperate layer.
G-code snipit of code with first cut set to no lead in and 2 nd cut set to wiggle pierce:
G92 Z0.
G38.2 Z-5.0 F100.0
G38.4 Z0.5 F20.0
G92 Z0.0
G0 Z0.02 (IHS Backlash)
G92 Z0.0
G0 Z0.15 (Pierce Height)
M3
G1 Z0.125 F100.0 (Cut Height)
H1
G1 Y1.0 F30.0
H0
M5
G0 Z1.0
G4 P0.5
G0 X11.4779 Y19.2265

G92 Z0.
G38.2 Z-5.0 F100.0
G38.4 Z0.5 F20.0
G92 Z0.0
G0 Z0.02 (IHS Backlash)
G92 Z0.0
G0 Z0.15 (Pierce Height)
M3
G1 Z0.125 F100.0 (Cut Height)
H1
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131 F100.0
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G2 X11.4779 Y19.2265 I0.1122 J-0.1141
G3 X11.2525 Y19.2274 I-0.1131 J-0.1131
G1 X11.2516 Y19.2265 F30.0
G3 X10.2587 Y16.8293 I2.3971 J-2.3971
G3 X13.6487 Y13.4393 I3.3901 J0.0
G3 X17.0388 Y16.8293 I0.0 J3.3901
G3 X13.6487 Y20.2194 I-3.3901 J0.0
G3 X11.2516 Y19.2265 I0.0 J-3.3901
G3 X11.2516 Y19.0454 I0.0905 J-0.0905
H0
M5
G0 Z1.0
G4 P0.5

Exact same G-code snipiy with wiggle option turned off. Notice my pierce time is back.
G92 Z0.
G38.2 Z-5.0 F100.0
G38.4 Z0.5 F20.0
G92 Z0.0
G0 Z0.02 (IHS Backlash)
G92 Z0.0
G0 Z0.15 (Pierce Height)
M3
G4 P1.7
G1 Z0.125 F100.0 (Cut Height)
H1
G1 Y1.0 F35.0
H0
M5
G0 Z1.0
G4 P0.5
G0 X11.4779 Y19.2265

G92 Z0.
G38.2 Z-5.0 F100.0
G38.4 Z0.5 F20.0
G92 Z0.0
G0 Z0.02 (IHS Backlash)
G92 Z0.0
G0 Z0.15 (Pierce Height)
M3
G4 P1.7
G1 Z0.125 F100.0 (Cut Height)
H1
G3 X11.2516 Y19.2265 I-0.1131 J-0.1131 F35.0
G3 X10.2587 Y16.8293 I2.3971 J-2.3971
G3 X13.6487 Y13.4393 I3.3901 J0.0
G3 X17.0388 Y16.8293 I0.0 J3.3901
G3 X13.6487 Y20.2194 I-3.3901 J0.0
G3 X11.2516 Y19.2265 I0.0 J-3.3901
G3 X11.2516 Y19.0454 I0.0905 J-0.0905
H0
M5
G0 Z1.0
G4 P0.5
G0 X15.0596 Y23.6357

Anyway to get both pierce delay on wiggle and no leadin cuts in same g-code file?

[mechanicjon]

I figured out a work around/way to do it. Setup another tool without wiggle and use it for the layer where no wiggle is needed.